8,000 tons. currently , the extracted rubbish is being unloaded into the receiving hopper. later along the technological chain, this chalk is mixed with additional components for the preparation of soybean mixture. here is our natural chalk, which makes up 80% of our final cement product. in addition to chalk in the composition of cement.

accompanying material for the extraction of chalk, or we produce sand from the bed of the sosh river. after the main and corrective additives , the soy mixture enters the crusher, where it is preliminary crushed to fractions of no more than 50 mm, the mixture is fed by belt conveyor to an online analyzer, with the help of which the shift chemist on duty at the testing center...

adjusts and adjusts any parameters for the required raw mixture. subsequently , the soy mixture is fed to a hammer crusher, where under the influence of high temperatures of about 700° celsius, drying and production of soy flour occurs. after the crusher dryer, the soy flour enters. to the separator, where the larger fraction is separated and returned to technological process, and the finer fraction enters the power for storing aged flour, where the production stage is completed in this workshop; in the future, the clinker production technique will be used. the main product obtained by the firing shop is clinker, which is a semi-finished product for... cement. clinkers are

granules made from flour. the heart of our plant is the clinker firing workshop, where raw flour from the silo is supplied to the kiln unit through a heat exchanger. furnace unit parameters, diameter 4.8 m, length 72 m. all physical and chemical processes take place here, and the output is a semi-finished product clinker. fuel consumption per day is about 600 tons of coal and 600 tons of peat briquette. every day , about 9,000 tons of raw flour comes from the raw material grinding shop; at the exit from the whistling unit, we receive 5,000 tons of clinker per day. the temperature of clinker formation in the peak unit is 1500°c. the temperature at the torch is 2200°. natural gas is used only in the process.

depending on the minerals used additives, we can offer our consumers up to 15 brands of different cements. we are located in the cement grinding shop, where the main stage of the technological cycle, the production of finished products, portland cement, takes place. clinker from the sieve for storage through a hopper and by means of dispensers is supplied to a conveyor belt, followed by clinker. gypsum

stone is added; in this case, granulated slag is added as a mineral additive; sand can act as a mineral additive. we will get sandy cement. if we we do not use mineral oak; we produce cement without additives. subsequently , this mixture is supplied for preliminary crushing to a roller press, upon exiting which the material is sent to a closed-circuit ball mill. the output is 150 tortlan cement per hour. the maximum productivity of two technological lines for cement grinding is 7200 tons of cement per day. additive cement without before... these are the setting time and strength, that’s all, if you make a little fence or a post at your dacha, that’s enough for you you will make any cement with additives, you are not going to use a bulldozer, but if you are building a bridge structure, naturally you need this structure

to gain power as quickly as possible to ensure the load, let’s say up to 500 kg per square cm. after exit from the mill, the finished partlan cement is sent by a belt conveyor for storage and further shipment with a capacity of 10,000 tons of cement each. each brand of cement is stored in a separate silo, then cements are stored in villages through a loading device is loaded into cement wagons, into road transport, or enters the packaging line and is subsequently supplied to our consumers. we export the cement we produce to the russian federation.

carrying out the process of producing cement is a fairly intensive process; from the moment the chalk enters the receiving bank until the finished cement leaves the grinding mill, it takes no more than 30-40 minutes. the production capacity for cement production is 1,572,000 tons of cement per year. the main division of technological process control is

this is iron ore, we get a ready-made raw mixture, which then goes through the dryer-crusher, we get this kind of raw flour, which is stored in a flour silo and is later used in the roasting process, the firing shops, after the raw flour leaves

the furnace unit, we get the main semi-finished product - clinker. by grinding clinker in technological lines, mills with natural gypsum, we obtain without... the division is accredited for more than 90 raw materials ending with finished products. our types of tests. unit tasks incoming control of raw materials, familiarization with the accompanying documentation, selection of materials, chemical, physical and mechanical tests, and a conclusion is given on the possibility of using these

waste components in the technology. the current control group is testing control during the production process, starting from raw materials, finished raw materials.

product production and shipment are carried out around the clock, except for stops for regulated repairs and equipment maintenance. the main specialties for the company in which we attract young people are: specialists are mechanics, repairers of control and measuring instruments, engineers and technologists, as well as specialists in working specialties, these are mainly welders and repairmen.

the history of the enterprise is years of continuous development, the main goal has always been to increase the productivity of equipment, the commissioning of a new production line since 2013, the enterprise radically changed the production flow chart until 2013.

the new production line allows for the production of products and productivity is 3-4 times higher while reducing costs by up to 20%. with the introduction of a new technological line and a decrease in the volume of slate consumption, the company stopped producing slate in 2017; there is constant

interaction with our consumers to identify the need for new types of products. with certain characteristics, so the company does not stop there and sets itself the task of annually offering our consumers new types of cement for various structures, as well as building mixtures for market of the russian federation. i was born in the neighboring sveslavsky district, graduated from a rural school and after graduating from a higher educational institution, by the will of fate i ended up at this enterprise. in principle, i had to

work at a completely different company. i was assigned according to assignment. to my native msislavsky district, however, it turned out that the place to which i was sent was already filled, so by the will of fate, having received my dismissal, i began to independently search for my first job , and as i remember now, the date was march 29, 1999 year, i was hired as an economist in the economic department for the production of cement slate, and since then i have considered myself a cement worker. from the moment i was hired in the planning and economic department of the enterprise , i went through basically all the stages: economist, leading economist, head of the plan of the economic department, and now since october 2004 i have been working as deputy general director for economics, and this is how it has developed over

the years of work. proposal for management of other incentive measures: development of long-term development plans for the introduction of new types products and production, which will improve production efficiency,

financial performance, and increase profit margins, which will ultimately improve the well-being of our employees. industrial facility created by human labor increases the tranquility of nature.

we confidently step into a new day. we do this to our music, the music that sounds inside each of us, it is everywhere in the sun, in timid movements, at the tips of our fingers, music inspires, makes us think and opens up thousands of expensive music can change the world because it can change us. music is inside each of us.